LM607 DATASHEET PDF

LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.

Author: Tegore Molabar
Country: Grenada
Language: English (Spanish)
Genre: Video
Published (Last): 17 February 2010
Pages: 298
PDF File Size: 4.74 Mb
ePub File Size: 16.70 Mb
ISBN: 493-8-40498-505-2
Downloads: 46679
Price: Free* [*Free Regsitration Required]
Uploader: Tygosho

Documents Flashcards Grammar checker. They are based on a buried zener reference as pioneered in the LM references, but dataeheet not require any heater, as they rely on special temperature-compensation techniques Patent Pending.

The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. The Llm607 also provides excellent stability vs. The devices have a A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0.

Unless otherwise noted, these conditions apply: These limits are not to be used to calculate outgoing quality levels. The LM has a Datashheet B output, and will exhibit transients at the crossover point. This point occurs when the device is required to sink approximately 1.

LM607 View Datasheet(PDF) – National ->Texas Instruments

In some applications it may be advantageous to pre-load the output to either Vin or to ground, datasueet avoid this crossover point. Thermal regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW. There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation.

datassheet Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Regulation is measured at constant temperature using pulse testing with a low duty cycle.

  BARICCO OCEAN SEA PDF

Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Tempco. Consult factory for availability of devices with Guaranteed Long-term Stability. Consult factory for availability of devices with tighter Accuracy and Tempco Specifications.

In Sinking mode, connect 0. A military RETS electrical test specification is available on request. LM see curve above: Trimming to a wider range is possible, but is not recommended as it may l607 the Tempco and the Tempco linearity at temperature extremes. For example, if the output were trimmed up to The output can sink current as well as source it, but the output impedance is much better for sourcing current.

The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to dattasheet.

LM Datasheet(PDF) – DATASHEETBANK

The output is short-circuit-proof to ground. However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature. The device does not include a thermal shut-down circuit. If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur.

Avoid such overloads for voltages higher than a 20 V, for more than 5 seconds, or, at high ambient temperatures. Its long-term stability pm607 typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. Contact the factory for availability of devices with proven long-term stability.

The LM is recommended for applications where the highest stability and lowest llm607 is required over the full military temperature range. The LM is suitable for limited-temperature operation. The curves showing the Noise vs. Capacitance in the Typical Performance Characteristics section show graphically that a modest capacitance of 0. The capacitor used should be a low-leakage type. Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise.

  HA13155 DATASHEET PDF

LM Datasheet PDF – National ->Texas Instruments

Dtasheet not connect anything to these pins, or improper operation may datasheef. These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them dataxheet from large transients or AC signals, as stray capacitance could couple noises into the output.

These pins may be cut off if desired. Alternatively, a shield foil can be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively acting as a guard against AC coupling and DC leakages. The trim pin pin 5 datqsheet also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere.

Pin numbers for H, M or N packages. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.

A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its daatasheet or effectiveness. National Semiconductor Europe Fax: Tsimshatsui, Kowloon Hong Kong Tel: This datasheet has been downloaded from: